Главная

Популярная публикация

Научная публикация

Случайная публикация

Обратная связь

ТОР 5 статей:

Методические подходы к анализу финансового состояния предприятия

Проблема периодизации русской литературы ХХ века. Краткая характеристика второй половины ХХ века

Ценовые и неценовые факторы

Характеристика шлифовальных кругов и ее маркировка

Служебные части речи. Предлог. Союз. Частицы

КАТЕГОРИИ:






Service instructions





9.2

 

 


 

  P.O. numer/ Date   4530022493-013 Date: 09.07.2015
  Oreder number/ Position:   O106 72332159 400
  Description:   Helical gear unit with adapter
  Type:   RF27 AM80/II2GD
  Your material number:   F01/30006327-000040.0100
  Quantity:    
       
       
  Serial number:   01.7233218604.0001.15
  Speed [r/min]   : 1400 / 250
  Max. output speed [r/min]   : 250
  Max. input speed [r/min]   : 1400
  Total ratio [I]   : 5,60 / finite
  No. of teeth nom./denominator   : 28/5
  Output torque [Nm]   : 55
  Max. overhung load [N]   : 1310
  Service factor FB   : 1,00
  Mounting position   : M4
  Lubricant / -volume [l]   : CLP HC 68 Synth.Oil / 0,70
  Max. input torque [Nm]   : 10,00
  Surface protection   : OS1 to technical data sheet 01802__94
  Paint coat   : Top coat RAL7040 (window gray)
  Assembly specifications   : ATEX gear unit to
      assembly instructions 017570302
       
  Output shaft end   : 25x50mm Ig.
  Flange   : 140mm
  Output oil seal   : 2 oil seals
  EX protection gear unit   : II 2GD c,k T4/T120C
  Enclosure reducer [IP]   : 65
  Ambient temp. gear unit [°C]   : -30... +50
  Documentation no. A   : 20050542
  Parts list   : 0125208998
       
  Bore on input side   : 19mm
  Parts list   : 232620500
       
  Nameplate   : English
  Nameplate position   : Attached to the gear unit
  Text of gear unit nameplate   : 250/1400 UMP
  Opera.instr. A lang./quantity   : English /1
  Commodity code   : 84834021
       
       
             

 


 

SEW-EURODRIVE GmbH & Co KG Ernst-Blickle-Straße 42, D-76646 Bruchsal

declares under sole responsibility that the following products are in compliance with the basic health and safety requirements of Directive 2006/42/EC, appendix I:

 

1.1.1 — 1.1.3 /1.1.5/1.3 /1.3.1 — 1.3.4/1.3.6 — 1.3.8/1.3.8.1 /1.3.8.2/

1.4/1.4.1 /1.4.2 /1.4.2.1 /1.4.3 /1.5/1.5.2 — 1.5.9 /1.5.16 /

1.6/1.6.1 /1.6.2 /1.6.5 /1.7/1.7.1 /1.7.2 — 1.7.4 /1.7.4.1 — 1.7.4.3 /

 

gear units of the series R..; RES F.. K..; KES S.. W.. H..
Applied harmonized standards: EN ISO 12100:2010

 

The products are intended for installation in a machine. Putting these products into service is prohibited until it has been established that the machine into which the products are to be incorporated complies with the provisions of the applicable directive.

 

The special technical documents for partly completed machinery have been created and can be made available to the national authorities in response to a reasonable request.

 

 

Bruchsal 15.10.13  
Place Date Johann Soder Managing Director Technology a) b)
a) Authorized representative for issuing this declaration on behalf of the manufacturer b) Authorized representative for compiling the technical documents

 


 






Не нашли, что искали? Воспользуйтесь поиском:

vikidalka.ru - 2015-2024 год. Все права принадлежат их авторам! Нарушение авторских прав | Нарушение персональных данных